Features

• Align Trex T-REX 600EFL PRO Super Combo KX016017

Instruction(3GX Programmable Flybarless System):

• Brand new redesigned 3GX represents a new generation of multi function flybarless system. The dramatically improved performance will create immediate impact on any enthusiasts.

• 3GX is currently the smallest and lightest flybarless system on the market. Two ports to directly connect Spektrum and JR satellite receivers, along with full support of Futaba's S-BUS system.

• Based on the 3G FL760 manual setup process, the 3GX can be setup in a few minutes through a simple process. In addition, the 3GX can support all of the CCPM swashplate system currently on the market including 90, 120, 135, and 140 degrees swashplates.

• Graphical illustrated instruction on the computer setup software directs the user through a step by step setup process, allowing for quick setups without omitting any steps.

• Support Bluetooth connectivity. With the soon to be released Bluetooth connectivity kit, 3GX can be programmed wirelessly from a PC. Eventually there will also be smartphone apps allowing live adjustments to 3GX without powering down.

• With 3GX's built in Align RCE-G600 governor function, no external governor is needed to reduce electronic wire clutters.

• A library of pre-configured 3GX settings specifically available for T-Rex series of helicopters, allowing pilots to achieve the most optimal setup for their helicopters.

• Three levels of flight mode is available on the 3GX to provide different feels from beginners to advanced pilots.

• Custom parameters have been opened up in 3GX to allow pilots to fine tune numerous settings for swashplate and rudder. Settings export feature allows custom settings to be shared amongst friends.

• 3GX utilizes brand new gyroscope sensors of the highest specifications when compared to other flybarless systems currently on the market, allowing it to be used under harsh conditions. Dual axis plus rudder sensor dramatically improves swashplate and rudder correction precision compared to last generation 3G. This is clearly noticeable in stable hover as well as highly aerobatic routines.

• Suitable for helicopter of all class from 200 to 700, glow engine or electric powered. The superior vibration resistant characteristic is evident even when mounted with harder double sided mounting tape.

• 3GX utilizes 16 bit processor which is 4 times faster than previous generation, along with a completely re-written firmware. The result is a dramatic stability improvement from previous generation, with stability that rivals a flybarred helicopter, yet posses explosive agility.

• With built in pirouette compensation function, 3GX is able to stabilize the helicopter on a fixed point during pirouetting maneuvers. Pirouetting flips type of maneuvers are easily accomplished with precision.

• 3GX's rudder control is similar to the high end GP-780 gyro in that rudder sensitivity is catered specifically for the helicopter's rudder response characteristics, allowing consistent rudder feel even under high speed conditions. This excellent control feel will allow pilot of all skill levels to experience the perfect integration between 3GX and helicopter.

• Additional peripherals planned for the 3GX includes 3-axis accelerometer, 3-axis magnetic compass, and GPS positioning system. While the commonly available position hold gyro system utilizes only 6 sensors, 3GX’s total of 10 sensors ensure positioning of helicopter with superior accuracy, providing the ultimate solution for aerial photography or other special purposes.

T-REX 600EFL PRO Super Combo:

• New aerodynamically efficient low drag flybarless head assembly,with detachable blade grip pitch arm for ease of maintenance.

• The frame utilizes 2mm carbon fiber plates of the highest spec. Patented composite material construction technique cleverly utilize frame space that improved overall rigidity, and also created a minimalistic beauty.

• Innovative sliding battery tray rails imbedded into the 3K side frames, with patented spring loaded latching mechanism, allowing for quick battery access as well as battery protection.

• Top mounted motor base bringing the motor’s center of gravity closer to rotating disc, improving 3D agility.

• Brand new 600 class 12S high voltage brushless motor providing generous torque and power output, yet consumes lower average current to prolong the life of batteries.

• The most optimal motor pinion ratio and tail gear ratio to achieve the most efficient power output and flight characteristic.

• Heatsink embedded into motor mount for effective cooling of motor.

• Motor mount consists of third bearing block to provide motor shaft support, effectively reduce torque induced shifts, and minimize gear striping issue.

• Utilize direct link CCPM swashplate control system to enable direct and fast control response. Specially designed anodized CNC servo horns are not only visually pleasing, but are extremely rigid.

• Utilizes highest spec CNC modue-1 helical main gear, with highest load tolerance and lowest noise.

• Ergonomically designed H-shaped electronic mount to provide flexible organization or equipment, and minimize wire clutter.

• Brand new CNC machined metal tail gear box, with thicker side plates to increase rigidity. The more streamlined design also allows for simpler disassembly.

• High quality 5mm carbon rod and CNC metal tail scissor control arms are used in rudder control system to improve rudder lockingand control effectiveness.

• Additional radial bearing is added to the one way bearing block to ensure smooth rotation, and eliminate jammed one way bearing.

• Tail pitch mechanism equipped with high precision bearing.

• High speed thrust bearings in tail blade grips.

• New lightened landing gear assembly with lower center of gravity.

• High quality painted fiberglass canopy with 4-point quick release mounts.

Users must have a certain concept of security to operate the R/C helicopters.
Be sure to read and comply with related safety notes of instruction manual before flying.

Specifications(3GX Programmable Flybarless System)

• Operating Temperature:-10~60 degree

• X and Y axis Operating Angle Range:-300~+300 degree

• Z axis Operating Angle Range:-600~+600 degree

• Size:36.5x25.2x15.6 mm Size

• Weight11g Weight

• Supports Wide/Narrow Bandwidth Digital and brushless servos

• Spektrum and JR Satellite antennas support (Replaces original factory receiver)

• Futaba S.BUS system support

• Built in governor function

• Maximum working voltage:8.5V

• Compatible with 1024/2048 resolution Spektrum receivers

• Supports 90/120/135/140 CCPM swashplates

• Field setup without the use of a PC

• Compatible with 2 to 5 blades rotor heads

• Support up to 6 servos

• Automatic servo type recognization

Specifications(T-REX 600EFL)

• Length: 1160mm

• Height: 353mm

• Width: 210mm

• Main Blade Length: 600mm

• Main Rotor Diameter: 1347mm

• Tail Rotor Diameter: 260mm

• Motor Drive Gear:13T

• Main Drive Gear:112T

• Autorotation Tail Drive Gear: 131T

• Tail Drive Gear: 34T

• Drive Gear Ratio: 1:8.61:3.85

• Weight(With Motor): 2290g

    Package Contents

• Align T-REX 600EFL PRO Kits Set X1

• Aluminum Tail Boom X1

• 600 3G Carbon fiber blades X1

• 600MX Brushless Motor(510KV) X1

• DS610 Digital servoX3

• DS650 Digital servo X1

• 3GX Flybarless System X1

• Castle ICE HV 80 Brushless ESC X1

• 6A External BEC w/ 5.1V Two-way Step-down voltage regulator X1

Provided by user's power Equipments:

• Transmitter(7-channel or more, helicopter system)

• Receiver(7-channel or more)

• 6S Li-Po 2600 ~ 4600mAh X2 (3300mAh suggestion)

• Dial Pitch Gauge